|
|
91:
|
cutting out above 5000 RPM
(Technical Discussion & Questions - by rickburns, started: 04-21-2014, last post: 2014-04-26 23:26:12 CEST)
Ideas on what will cause the engine to cut out above 5000 RPM. Sounds like it's hitting a rev limiter, but that is set higher than that. Could it be a fuel pump going out? Simple as a fuel filter? New dist cap, rotor and module. Does it with or without air filter, so air is good. Thanks.
Score: 475, Size: 12483 bytes
|
92:
|
Transmission swap guru's, need your help asap.
(Technical Discussion & Questions - by JHarvey, started: 10-06-2013, last post: 2013-10-07 20:21:24 CEST)
Alright heres the situation, I have an 87 GT (Automatic) The car is a daily driver and before I started the auto to manual swap i installed the manual computer to make sure it worked. It took about 20seconds to crank but after it cracked it ran fine. After shutting the engine off and turning it...
Score: 475, Size: 17495 bytes
|
93:
|
3.8 engine swap
(Technical Discussion & Questions - by johnguzman1212, started: 06-16-2014, last post: 2014-11-06 05:45:16 CET)
I own a 87 fiero 2.5 im thinking about doing a engine swap. been watching all the posts. What is the best 3.8 SC engine to get from what car which is easiest to do? and which engine to stay away from? im sure I can do it . can I keep my auto transmission? I can afford 5000 plus
Score: 475, Size: 19965 bytes
|
94:
|
87 gt 5 speed won't start
(Technical Discussion & Questions - by jessesmith121, started: 04-08-2016, last post: 2016-04-26 04:49:06 CEST)
Hey all, I recently purchased an 87 gt 5 speed.. it won't start. It has fuel pressure and spark to the coil. I replaced the ICM and still no joy.. even with starting fluid. Any other thoughts? The PO said th eyes were driving it on the highway and it just stopped running... the motor turns...
Score: 475, Size: 33455 bytes
|
95:
|
Paddle shifting the 4T65E
(Technical Discussion & Questions - by phonedawgz, started: 05-23-2021, last post: 2021-06-06 17:05:37 CEST)
4T65E paddle shifting. Since the 4T65E shifts are electronically controlled, and since it can be done, thoughts on converting to manual paddle switching? Ok, a few things come to mind. Arduino controlled, manual/automatic switch somewhere, and programming in the Arduino to make sure I don't...
Score: 475, Size: 10923 bytes
|
96:
|
fuel pump fuse keeps blowing ended up on a tow truck
(Technical Discussion & Questions - by boostme, started: 05-31-2014, last post: 2014-06-01 22:41:35 CEST)
I have a harness from reddevildriver.com and everything has been going great the last year or so. I upgraded my battery cables to a 0 gauge for the relocation kit today and drove about 5 miles on the highway. A number of fuel pump fuses have blown upon my testing. I thought it might have been the...
Score: 475, Size: 9639 bytes
|
97:
|
88 2.5 starts but shuts off a second later
(Technical Discussion & Questions - by 2002z28ssconv, started: 03-17-2015, last post: 2016-07-19 16:31:33 CEST)
Give me some ideas. My daughter's car was running fine, shut off to go inside a theme park. Now it starts up just as normal but then stalls out. It sounds like the ignition shuts off. The fuel pump is running. 3/4 tank of gas. It runs smooth for the second it runs. Starts every time you hit the...
Score: 475, Size: 32929 bytes
|
98:
|
TunerPro RT not connecting to 7730
(Technical Discussion & Questions - by ConvictedRedneck, started: 04-21-2012, last post: 2013-07-28 20:40:23 CEST)
I'm having trouble getting TunerPro v5 to connect to my 7730 ECM. Phonedawgz, I followed all the directions in your "Using tunerpro RT as a scanner setup" thread but am still having trouble.I'm using the Moates extreme ALDL USB cable. Should it be on the 10k resistor or open setting?Either way, I...
Score: 475, Size: 7042 bytes
|
99:
|
Is it possible to get ignition keys for our old cars cut using the VIN ?
(Technical Discussion & Questions - by Patrick, started: 07-11-2014, last post: 2015-07-09 03:05:31 CEST)
I've had an '88 Formula for just under a year. The ignition lock has often been very finicky to turn (either way). Sometimes I'd have to fiddle with it for a few seconds, and sometimes it would take longer. Last night it decided it wasn't going to turn... period.I suspect the problem might be the...
Score: 475, Size: 35006 bytes
|
100:
|
How to measure volt on injector row??? Last change
(Technical Discussion & Questions - by Gambit, started: 03-04-2014, last post: 2014-03-17 19:26:47 CET)
Hi guys, question, how do i measure if there is voltage on the injectors. I know the big connector has 6 wires, 2 wires for one injectorset of 3, 2 for the other row of injectors and 2 for the cold start. How must i measure that there is voltage on both injector rows? My engines wants to start but...
Score: 475, Size: 21774 bytes
|
| |
|
Put a PFF Search Box on your Site!