|
|
41:
|
Crx intake tubing size, fiero throttle body od?
(Technical Discussion & Questions - by lordbg0205, started: 10-06-2017, last post: 2017-10-07 05:33:43 CEST)
Yeah I know it's loud, no up gains, don't care. I've been rocking Rodneys setup for 2 years, and it's good, time to clean up the engine bay. I see everybody uses the 3" but with that stupid looking coupling that reduces it down to what 2.5" just doesn't look good to me. Does anybody know the...
Score: 1000, Size: 58 bytes
|
42:
|
Throttle body identification
(Technical Discussion & Questions - by OriginalDoug, started: 08-04-2017, last post: 2017-08-08 22:34:39 CEST)
This place is a gold mine for new fiero owners like me, and I'm hoping for another success here.What is the hole to the right of the tps and iac in this picture?http://captfiero.com/distri...uild/thumbs/tn_3.jpgThis isn't my fiero in the picture but it was the best picture I could find of it. Many...
Score: 1000, Size: 41 bytes
|
43:
|
Popping back thru throttle body
(Technical Discussion & Questions - by DirtyDawg, started: 06-18-2017, last post: 2017-07-12 14:18:27 CEST)
Can't seem to figure out, car ran great then all of a sudden you can't give it any gas it just pops back thru throttle body and want idle, starts up. 2.8 has done this in the past but would clear out. Looking for suggestions, Thanks
Score: 1000, Size: 41 bytes
|
44:
|
2.5 throttle body swap 4.3
(Technical Discussion & Questions - by mthickey, started: 06-23-2017, last post: 2017-06-26 21:46:30 CEST)
So I just got my 86 fiero, and there are several upgrades I want to do to it, but getting performance out of the iron duke seams difficult. The consensus seam to mostly be that the tiny throttle body is one of the biggest restrictions, followed closely by the head. My plan is to swap the stock...
Score: 1000, Size: 35 bytes
|
45:
|
iron duke running rich, idling rough, flames from throttle body
(Technical Discussion & Questions - by TheIronDuke84, started: 04-16-2017, last post: 2017-04-17 03:44:01 CEST)
Hey folks, I've got an '84 Indy Fiero with an iron duke, ported and polished, headers and dual exhaust, along with an upgraded throttle body(I think a Holley). I got it just the way it is. I have treated the fuel and replaced the fuel filter, air filter, cleaned the engine, flushed the coolant...
Score: 1000, Size: 77 bytes
|
46:
|
1988 2.5L Auto Throttle Body Replacement
(Technical Discussion & Questions - by slickster, started: 03-02-2017, last post: 2017-03-07 05:46:48 CET)
According to the interchanges, the only throttle bodies compatible with the 87-88 4 cylinder Fiero's are as follows:Buick Skylark '87 2.5LBuick Somerset '87 2.5LOlds Calais '87 2.5LPontiac Grand Am '87 2.5LDoes anyone know if later models such as an 88-91 will work?Also, I...
Score: 1000, Size: 50 bytes
|
47:
|
For sale northstar throttle body
(The Mall - by crashmydaytona, started: 02-05-2017, last post: 2017-02-16 16:00:23 CET)
One extra large bore 75MM NORTHSTAR throttle body. This throttle body will fit 3800SC engines and really wakes them up allowing better air flow and throttle response. It can be used with the ZZ Performance adapter plate that allows it to bolt right to a 3800 supercharger or N/A manifold. It comes...
Score: 1000, Size: 47 bytes
|
48:
|
FS: Adapter for gen 5 M90 to Northstar throttle body
(The Mall - by doublec4, started: 04-14-2016, last post: 2017-02-10 02:44:26 CET)
$75 for the adapter + hardwareI bought the gen 5 adapter by accident... I needed the gen 3This will allow you to run a 2000+ 75mm Northstar throttle body on your supercharger. pm or post if you're interested.Thanks!
Score: 1000, Size: 61 bytes
|
49:
|
3800 throttle body spacing adapter with new gasket
(The Mall - by mmeyer86gt/gtp, started: 01-28-2017, last post: 2017-01-29 04:35:31 CET)
3800 throttle body spacing adapter with new gasket you will need to source new screws for this$30 shipped
Score: 1000, Size: 65 bytes
|
50:
|
Need help with 3800SC Series III with Northstar Throttle Body MAF sensor. How? Where?
(Technical Discussion & Questions - by JohnWPB, started: 12-31-2016, last post: 2017-01-04 23:21:23 CET)
I am almost finished with my swap, and can not get the engine to run. I have 90 PSI fuel pressure before the regulator, and reading 52 PSI on the fuel rail. All the specks I have found for the Series III engine say that 50-55 PSI fuel pressure is idea. The plugs are all new, and gapped to specs,...
Score: 1000, Size: 93 bytes
|
| |
|
Put a PFF Search Box on your Site!