91:
|
4.9 Auto Shifter Adapter Info needed
(Technical Discussion & Questions - by jokerb90, started: 11-15-2014, last post: 2014-11-16 16:48:38 CET)
Second 4.9, first autoHave 4.9 in car, realized shift cable is not just plug and play.....d'ohTried search, maybe using the wrong terms. Need a how to using the caddy bracket, as the stock one is gone. Please assist, pictures are awesome,[This message has been edited by jokerb90 (edited...
Score: 499, Size: 46 bytes
|
92:
|
4.9 Caddillac Cooling System Bleeding Procedure
(Technical Discussion & Questions - by BobFitz, started: 08-16-2015, last post: 2015-08-16 21:06:01 CEST)
New owner of an 87 GT with a Caddy 4.9 swap. I need to know the correct procedure to fill and bleed the air from the cooling system.Bob
Score: 499, Size: 55 bytes
|
93:
|
Tunerpro RT and the 4.9 engine.....
(Technical Discussion & Questions - by MadProfessor8138, started: 04-10-2017, last post: 2017-04-14 00:32:48 CEST)
Has anyone used the Tunerpro RT program to scan their 4.9 ?I have a question that I can't seem to find the answer to.......Can anyone help ?
Score: 499, Size: 52 bytes
|
94:
|
oil cooler 4.9 caddy engine
(Technical Discussion & Questions - by northstar, started: 09-13-2013, last post: 2013-09-14 03:01:41 CEST)
I poked a hole thru my oil cooler. I have a 4.9 out of a what I believe to be a 1995 4.9 does anyone have one .. a pic of one, and the total outer dimensions.w x h x l thanks c-note.....
Score: 499, Size: 37 bytes
|
95:
|
Let's replace my 88's 2.5 with a 4.9!
(Technical Discussion & Questions - by Reallybig, started: 04-26-2012, last post: 2018-06-10 19:40:27 CEST)
I haven't seen a 4.9 swap in a while so I figure I'll start posting my progress... Truth is I just figured out how to resize my pictures to work with PIP. I have found that following other peoples progress to be a great source of motivation and hope that posting my swap will inspire others with...
Score: 499, Size: 47 bytes
|
96:
|
4.9 with Stickpony Chip Check Engine ON but no code
(Technical Discussion & Questions - by falcon_ca, started: 06-07-2014, last post: 2014-06-10 23:52:46 CEST)
Title said it allWhere should I look other than the wires ?
Score: 499, Size: 62 bytes
|
97:
|
Help needed with 4.9 troubleshooting
(Technical Discussion & Questions - by d20180, started: 05-01-2016, last post: 2016-05-08 19:51:43 CEST)
I have a 4.9 (92 seville) swap that I bought several years ago and drove home. I am trying to get it going now after sitting for several years, but it won't start.I replaced the gas and the fuel pump. (pressure tester ordered to verify pressure)If I give it a shot of ether it will start right up,...
Score: 499, Size: 43 bytes
|
98:
|
4.9 oil filter housing o-rings question....
(Technical Discussion & Questions - by MadProfessor8138, started: 02-11-2017, last post: 2017-02-21 01:51:52 CET)
Does anyone know where I can buy the o-rings that go in the oil filter housing?Are they a dealer only item?
Score: 499, Size: 60 bytes
|
99:
|
4.9 Allante fuel rail inlet...?
(Technical Discussion & Questions - by HarryG, started: 10-20-2013, last post: 2020-04-24 22:20:39 CEST)
Apparently the engineers at Cadillac used a special inlet fitting for the Allante fuel rail. Every fuel rail I've seen is minus that fitting... Has anyone found a replacement for that fitting or a work-around solution?
Score: 499, Size: 38 bytes
|
100:
|
What is the 'best' 4.9 mount configuration?
(Technical Discussion & Questions - by imacflier, started: 02-16-2016, last post: 2016-02-20 15:06:22 CET)
Looking at 4.9 swaps there seem to be two or three configurations used: the two transmission mounts doing duty as rear engine mounts plus one front engine mount plus a torque strut (aka dogbone). This is the configuration Rockcrawl used. The Fiero Factory site says they use five mounts....that...
Score: 499, Size: 53 bytes
|
|