|
|
101:
|
Caddy 4.9 Cylinder Seals
(Technical Discussion & Questions - by BZAnathema, started: 09-02-2014, last post: 2014-09-03 02:31:54 CEST)
I have three bad cylinder liner seals. My Haynes manual says to carefully scribe alignment marks before pulling liners, but I suspect they've been moved from original position already. Can I pull all eight, recondition, hone, and reseal them (I have fresh O-rings) at home, or do I need to go to a...
Score: 499, Size: 35 bytes
|
102:
|
Need an experienced 4.9 mechanic.....please.
(Technical Discussion & Questions - by MadProfessor8138, started: 03-25-2018, last post: 2018-03-29 06:52:47 CEST)
Are there any 4.9 mechanics close to Kentucky on here?I have an issue with my 4.9 that I can't fix and I need some help before I just give up on this car.Symptom:1. Runs rich2. Has a dead miss 3. Backfires when throttle is advanced and then released- or- advanced and held at continuous rpm4. Have...
Score: 499, Size: 61 bytes
|
103:
|
Ed Parks 4.9 wiring harness mystery
(Technical Discussion & Questions - by paulcal, started: 09-01-2014, last post: 2014-09-02 02:48:40 CEST)
While under the car today I noticed a loose red wire with a large round terminal connector on it. Upon further inspection I also found a smaller purple wire coming out of the same bundle that was not connected to anything either. These are run along the front injector rail. They look like they...
Score: 499, Size: 43 bytes
|
104:
|
Need info for 1984 4.9 swap trany wiring.
(Technical Discussion & Questions - by Dave_m, started: 06-08-2014, last post: 2014-06-15 19:19:10 CEST)
I am putting a 1994 4.9 with auto trany in my 1984 fiero. I need to know where to put the trany gear selector switch wires to. Its a 7 wire plug and i am just pulling my hair out trying to get this together.
Score: 499, Size: 49 bytes
|
105:
|
4.9 idle air control motor
(Technical Discussion & Questions - by jeffndebrus, started: 03-18-2009, last post: 2013-08-30 22:42:39 CEST)
4.9 idle air control motorI am having an idle problem. The car idles very high when first started- 1700rpms for a minute then it suddenly drops to 1000rpms and then it surges back and forth several times before settling in at around 1100rpms. I can take my foot off the gas pedal and the car is...
Score: 499, Size: 38 bytes
|
106:
|
Is there a thread detailing a 4.9 swap using the getrag?
(Technical Discussion & Questions - by imacflier, started: 05-09-2016, last post: 2016-05-10 01:54:52 CEST)
There MUST be one....but I will be darned if I can find it. Can someone help me with a link to the thread?TIA,Larry
Score: 499, Size: 66 bytes
|
107:
|
4.9 swap - need help Thanks!
(Technical Discussion & Questions - by 87GT2M6, started: 01-27-2015, last post: 2015-01-31 00:20:28 CET)
First thanks for any help on this matter anyone can give me. A Plus will be coming your way if I have not already done so.Here's whats going on. I did a 4.9 swap on my Fiero GT (87) a little over a year ago, and today the service engine light turned on. My question is what could be causing this?...
Score: 499, Size: 36 bytes
|
108:
|
TunerPro RT vs 5.0 not able to connect to 4.9 ECM
(Technical Discussion & Questions - by falcon_ca, started: 05-19-2016, last post: 2016-05-22 15:02:21 CEST)
I had to completely reinstall my good old ASUS EEE with XP.So, I reinstalled TunerPro and the ALDL cable driver.Using a known good adx fileTunerPro dont see my cable.I tryed configuration on Com3 and Com4What is the magic trick I m missing .....
Score: 499, Size: 59 bytes
|
109:
|
4.9 Cad exhaust manifolds
(Technical Discussion & Questions - by tcincpOR, started: 03-17-2018, last post: 2018-04-02 00:22:57 CEST)
I'm doing a 4.9 Cad swap and I have a question about the R side exhaust. Just so that I can confuse everyone, this is the side that would be Front on the Cad but now is Rear on Fiero. My engine is out of a 1995 Deville. Some exhausts in pictures on this site I have noticed have 2 outlets...
Score: 499, Size: 34 bytes
|
110:
|
4.9 overheats with AC on
(Technical Discussion & Questions - by rickburns, started: 03-27-2013, last post: 2014-04-26 18:36:59 CEST)
My 4.9 engine overheats on hot days in city traffic with the AC on. It's converted to R134, has the stock Caddy compressor, stock condensor, four core radiator, extra push fans to augment the stock pull fan on the radiator/condensor pack, as well as an oil cooler. Without AC, I can run hard and no...
Score: 499, Size: 34 bytes
|
| |
|
Put a PFF Search Box on your Site!