|
|
31:
|
VDO fuel level gauge problems
(Archive: TD&Q - by Joe 1320, started: 10-11-2010, last post: 2012-01-11 09:57:59 CET)
Ever since changing over the VDO gauges, I have a fuel level gauge problem. My VDO gauge works, but the range is off. With a full tank, the gauge reads half. However, when the tank is almost empty the gauge reads just a hair above empty. What do I need to do in order to get the gauge to show...
Score: 775, Size: 40 bytes
|
32:
|
3000GT gauge cluster in 86 GT, need fuel level sending unit
(Archive: TD&Q - by Hulki U. My-BFF, started: 10-11-2009, last post: 2011-05-02 10:42:32 CEST)
I am in the middle of a 3000GT dash swap, and I have the cluster wiring completed except for the tach, and the fuel gauge. I know the stock sending unit for the Fiero is 0(empty) - 90(full) ohms. The 3000GT fuel gauge is the opposite, 90-0. Anybody know where I can get a sending unit for my...
Score: 775, Size: 77 bytes
|
33:
|
Need procedure for testing fuel level sender outside of the car
(Archive: TD&Q - by whitey078, started: 07-28-2011, last post: 2013-03-14 10:11:35 CET)
so before i put the tank in the car i really want to test out the 88 fuel sender to ensure that its' good while i have the tank out for the new fuel pump and filter. I'm building a kit so its not like i can plug it in and move the float and check as i dont even have a fuel gauge at the moment,...
Score: 775, Size: 75 bytes
|
34:
|
Replacement Fuel Level Sender Pictures
(Archive: TD&Q - by chaosfinity, started: 03-09-2008, last post: 2009-09-07 11:04:10 CEST)
This takes a little bit of work but comes out great.This is the link to the product.http://www.egauges.com/vdo_...der=0_90ohms&PN=SN38You have to drill out 1 the upper rivet because the ground wire is to thick to be sandwiched between the original metal mount and the new metal mount.You will not...
Score: 775, Size: 52 bytes
|
35:
|
fuel level sender ?
(Archive: TD&Q - by kendallville, started: 03-28-2013, last post: 2016-03-23 10:10:31 CET)
So I did a search found thread after thread on the sending unit . I however found none that answers my questions.I know it should read from 0 empty to 90 full ,I know how to check it to find the readings, and I have the tester.Mine reads in the car reads full when full but never goes lower than1/4...
Score: 775, Size: 34 bytes
|
36:
|
best source for fuel level sender?
(Archive: TD&Q - by garage monster, started: 07-28-2012, last post: 2016-03-23 10:12:10 CET)
My 87 GT needs a sender for the fuel gauge. I removed and cleaned it but it is still not accurate and sometimes reads totally wrong. Where is the best place to buy new?Thanks
Score: 775, Size: 51 bytes
|
37:
|
Need some help with a GM fuel level sending unit
(Archive: TO/T - by afRaceR, started: 03-24-2008, last post: 2009-09-07 11:20:05 CEST)
Alright.......this is the deal. I have a 97 GM 1-ton van. Fuel gauge is way off, it wraps around the gauge once and goes past full. Service manual says the gauge works with 0 ohms empty 90 ohms full. I have a signal generator that tells me the fuel gauge is operating correcty at this range. Checked...
Score: 775, Size: 58 bytes
|
38:
|
GM fuel level sending unit question
(Archive: TO/T - by jaskispyder, started: 10-14-2010, last post: 2012-01-11 09:52:33 CET)
Ok, 2001 Aztek...I was wondering how the fuel level sensor works on this. Does it simply use the 0-90 ohm range like the Fiero, with 0 being empty and 90 full?Next, I am looking at bypassing the sensor and just connectings the two wires with a resistor to mimic the 90ohms. Does anyone have a...
Score: 775, Size: 49 bytes
|
| |
|
Put a PFF Search Box on your Site!