41:
|
Shifter Thread Size
(Archive: TD&Q - by prostreet505, started: 03-06-2008, last post: 2009-09-07 11:05:06 CEST)
I have a stupid question. What is the thread size and pitch for the shifter handle? I want to make some aluminum T-handle shifters and need to find out the size and pitch. I did a search but came up with nothing.Craig
Score: 775, Size: 34 bytes
|
42:
|
Fiero Store ball joint thread size?
(Archive: TD&Q - by Winkie, started: 07-05-2008, last post: 2009-09-07 11:04:15 CEST)
What is the size of the castle nut that goes on the Fiero Store upper balljoints? I tried the stock Fiero ones and they don't seem to fit. I tried four other sizes and they didn't fit either. Anyone know?ThanksRyan
Score: 775, Size: 44 bytes
|
43:
|
Thread Size
(Archive: TD&Q - by MTFIERO, started: 08-18-2008, last post: 2009-09-07 11:03:52 CEST)
I was swapping my TBS to try to correct the problem of the motor breaking up around 2000 RPM's and the top screw broke when I tried to remove it. Does any one know what size thread it is? I'm thinking it's a metric size and wonder if it can be drilled and tapped to a standard 10-32 thread? Also...
Score: 775, Size: 21 bytes
|
44:
|
Stock shifter thread size?
(Archive: GFC - by Carver1, started: 08-15-2007, last post: 2009-02-19 10:52:51 CET)
Anybody know? My guage says 15 threads per inch, but what is the diameter? I am making custom shift knobs, and need to buy the inserts for our cars. I hate the set screw type. Pics and info to come! And they will be CHEAP!!!!!
Score: 775, Size: 36 bytes
|
45:
|
Thread size of the dust cover bolts
(Archive: TD&Q - by sspeedstreet, started: 06-25-2007, last post: 2009-02-19 10:45:23 CET)
Trying to reinstall the lower dust cover shield on my '88 Getrag. There are four bolts that hold it in place. At a glance I thought they were 6mm standard thread, but they don't fit. Darned if I can remember what I took out when disassembling it. Somebody help me here?Thanks
Score: 775, Size: 50 bytes
|
46:
|
How do I know if a shifter knob will fit, what is Fiero thread size?
(Archive: TD&Q - by 2.5, started: 08-20-2007, last post: 2009-02-19 10:45:00 CET)
On ebay one says it fits:1/2 in.-20 3/8 in.-24 3/8 in.-16 5/16 in.-18 Will any of these work?
Score: 775, Size: 74 bytes
|
47:
|
What size thread on tie rod ends?
(Archive: TD&Q - by ltlfrari, started: 11-25-2007, last post: 2009-02-19 10:44:27 CET)
Anyone know what size the thread is on the tie rod ends. I just want to run a die down them to clean up the old rusty threads since the rods themselves are fine. Are the fronts and rears the same?Thanks
Score: 775, Size: 44 bytes
|
48:
|
Need Steering wheel nut thread size, Stripped
(Archive: TD&Q - by perceptionist, started: 12-14-2007, last post: 2009-02-19 10:44:16 CET)
I had a bit of bad luck in the process of removing my steering wheel. The nut and the shaft (shown below) are completely stripped. To make matters worse, the puller caused the end of the shaft to mushroom out. I was able to shave most of the flared end off in order to get a die on there.Does...
Score: 775, Size: 62 bytes
|
49:
|
shifter thread size
(Archive: TD&Q - by floridafiero, started: 08-31-2006, last post: 2007-03-15 11:30:29 CET)
Curious as to what size our manual shifter arm threads are. Mine is an 85 GT 4spd if that matters. Thanks in advance.
Score: 775, Size: 34 bytes
|
50:
|
shifter thread size
(Archive: TD&Q - by floridafiero, started: 08-31-2006, last post: 2007-03-15 11:30:28 CET)
Curious as to what size our manual shifter arm threads are. Mine is an 85 GT 4spd if that matters. Thanks in advance.
Score: 775, Size: 34 bytes
|
|