|
|
81:
|
distributor cap screw broke off....
(Technical Discussion & Questions - by mnsportsguy1966, started: 08-15-2021, last post: 2021-08-16 14:20:25 CEST)
I broke off one of the original distributor cap screws right at the head of the screw when I was attemping to replace my cap and rotor, any suggestions on how to get it out? I tried to drill it but its so small I cant even get it to stay on the screw. Thanks in advance
Score: 149, Size: 3862 bytes
|
82:
|
Fiero 2,5l idle issues
(Technical Discussion & Questions - by tomdylka, started: 08-13-2021, last post: 2021-08-15 07:57:20 CEST)
Hello folks,since yesterday I have problems with the idle of my 2.5l Fiero. I think that this problem can have many causes. However, it is noticeable that the speedometer failed at the same time. The rest of the instruments still work but the speed is no longer displayed. Does anyone know a cause...
Score: 236, Size: 1505 bytes
|
83:
|
Can Oil Pressure Sensor be unplugged?
(Technical Discussion & Questions - by snyderman, started: 08-14-2021, last post: 2021-08-15 04:10:07 CEST)
Should I still be able to run my iron duke with the oil pressure sensor be unplugged?Thanks in advance.
Score: 149, Size: 564 bytes
|
84:
|
Connector part numbers help - C203 - C500 - new pins?
(Technical Discussion & Questions - by mcgavin, started: 04-13-2013, last post: 2021-08-15 02:01:33 CEST)
I am starting an engine swap and I'm trying to keep things as clean as possible on the wiring side. Does anyone know where to find new pins and or connectors, unassembled?I need parts for C203 (15 pins, between driver and passenger seat) and C500 (34 pins, at the battery).
Score: 449, Size: 24339 bytes
|
85:
|
3800 SWAP / vacuum ???
(Technical Discussion & Questions - by TXGOOD, started: 08-03-2021, last post: 2021-08-06 02:28:04 CEST)
I`m running a series 3 fuel rail on a 3800 swap in my 88.I`m using a FPR with an inlet / outlet and return. My car doesn`t have the expansion tank and the lines are all messed up anyway so I just leave the cap loose. With my swap I just want to put an aftermarket charcoal canister connected to the...
Score: 149, Size: 2918 bytes
|
86:
|
3800sc running hot when idling
(Technical Discussion & Questions - by pontiacfierokid1985, started: 06-30-2021, last post: 2021-07-13 05:50:31 CEST)
3800sc L67 Ok here is my problem I got a 3800sc 4 speed fiero. Not running the fiero T stat housing using the stock 3800 one. I just installed a new 180 t stat water pump is new also, intake gaskets have been done with 04+ series 3 intake manifold gaskets so not the plastic ones. When driving the...
Score: 299, Size: 16717 bytes
|
87:
|
3800 temperature sensor fell into the hole?
(Technical Discussion & Questions - by longjonsilver, started: 07-05-2021, last post: 2021-07-11 21:12:21 CEST)
i have diagnosed my faulty temperature gage as being the sender. So i bot a new one. Looked exactly the same as the old one. i tried to quickly put the new sensor in the hole of the old one and it seemed to slip down into the motor. i put my finger into the hole and something appeared to move...
Score: 236, Size: 10356 bytes
|
88:
|
Fiero keeps stalling
(Technical Discussion & Questions - by M.aaron80, started: 07-09-2021, last post: 2021-07-10 00:28:15 CEST)
I read somewhere about fieros stalling until it’s warmed up,I forget what causes this problem.temperature sensor? I have an 88 fiero 3.4 swap runs good and starts fine but will keep stalling until it’s warmed up. No high idle
Score: 236, Size: 581 bytes
|
89:
|
Looking for an engine and help swapping it in, in upstate New York
(Technical Discussion & Questions - by phonedawgz, started: 06-28-2021, last post: 2021-07-04 07:22:55 CEST)
Seventeen year old Zachery Hines and his grandfather were planning to bring his grandfather's 1987 Fiero GT back to running condition this summer. The engine had been swapped before, but the wrong combination balancer and engine were installed and it didn't last. The plan was to take it apart,...
Score: 299, Size: 7821 bytes
|
90:
|
TPS
(Technical Discussion & Questions - by meadeka, started: 06-25-2021, last post: 2021-07-03 18:58:27 CEST)
So I just bought my new TPS feeling very excited to get my fiero to be normal again…. Well I plug my computer in and the new TPS was reading 5 volts off! It is supposed to be at 0 or -1.25 volts. What is my problem here? I know it’s the right TPS because I ordered it from Rock Auto. Please...
Score: 299, Size: 6308 bytes
|
| |
|
Put a PFF Search Box on your Site!