|
|
191:
|
3.1 Rebuild ?s
(Archive: TD&Q - by Eric, started: 08-05-99, last post: 1910-01-20 08:12:27 AMT)
I have a few questions concerning my 3.2 rebuild I am undertaking. First of all, the balancing of the new crank has got me confused. My machinist said he could balance the 3.1 internally and retain the stock 2.8 flywheel. I questioned this, but he assured me that there were ways to do this and...
Score: 1000, Size: 22 bytes
|
192:
|
Grand Am 3.1
(Archive: TD&Q - by Kekipi, started: 05-05-2004, last post: 2004-10-15 10:18:26 CEST)
I have a 96 3.1 out of a grand am, I know it won't fit a fiero but was wondering if I should keep the intake Manifolds, heads and everything above the block incase I run across a rear wheel drive 3.1. Heads were redone, lower end went south. Mike
Score: 1000, Size: 21 bytes
|
193:
|
3.1 in a fiero
(Archive: TD&Q - by burbl, started: 01-20-2002, last post: 2002-05-11 09:54:27 CEST)
hell there everybody in fiero land, i have justpurchased a 84 fiero with a 2.5 and 4 spd trans. i would like to put a 3.1 v-6 in it. is therea place that has reliable information to performthis swap and the parts that i will need.. thanks from scott
Score: 1000, Size: 22 bytes
|
194:
|
Where to buy 3.1 kit?
(Archive: TD&Q - by Cooter, started: 06-08-2003, last post: 2003-11-10 11:11:21 CET)
I need to rebuild a 2.8 into a 3.1 and will need the crank, pistons and all the goodies for a 'normal' (stock rebuild) engine. Anybody know the most economical place to start looking?Thanks!
Score: 1000, Size: 30 bytes
|
195:
|
3.1 engine swap
(Archive: TD&Q - by circlegear, started: 04-12-2008, last post: 2009-09-07 11:04:51 CEST)
i just bought a 1987 fiero with a siezed 2.5 4 cyl eng 5 spd trans and would like to install a 3.1 with a 5 spd trans the donor car is my daughters wrecked 1991 sunbird which i got for free, i have the 3.1 eng, wiring harness and ecm from the bird, question will these fit in my fiero ?
Score: 1000, Size: 28 bytes
|
196:
|
3.1 swap
(Archive: TD&Q - by coyote, started: 05-01-2002, last post: 2002-08-25 11:44:20 CEST)
thinking of dumping a 3.1 efi into a fiero,out of an 92 firebird, have the complete car. wondering has anybody, seen, heard or done. there is a ton of performance stuff out there for this engine and it seemed like a good canidate.coyote
Score: 1000, Size: 17 bytes
|
197:
|
Conversion from 2.8 to 3.1 or 3.4
(Archive: TD&Q - by mr.Fiero, started: 12-14-2003, last post: 2004-07-10 10:38:31 CEST)
Tell that it is necessary to change to increase working volume of the motor?
Score: 1000, Size: 44 bytes
|
198:
|
3.1 or 3.4 heads on a 2.8 block??
(Archive: TD&Q - by Small town fool, started: 09-21-2007, last post: 2009-02-19 10:44:47 CET)
Hello to every one, new member here and I would greatly like some advice. I just traded a dirt bike for an 87 GT V6 5 speed. Long story short it needs a new moter. Can I put bigger heads on the stock block?
Score: 1000, Size: 51 bytes
|
199:
|
what you'll need for a 2.8, 3.1, 3.4L V6 swap into a 1988 4 cylinder Coupe
(Archive: TD&Q - by gtxbullet, started: 12-13-2011, last post: 2013-03-14 10:10:25 CET)
I just finished installing a 3.4L and Getrag in my 1988 Fiero Base Coupe 2.5L 5-speed IZUZUI did the swap myself and learned a lot of things about just how different the V6 swap is on an 88 4 cylinder Coupehere is a short list of things YOU MUST HAVE and DO to make it work:V6 Fuel pump and Fuel...
Score: 1000, Size: 86 bytes
|
200:
|
'92 Beretta 3.1 Engine Swap
(Archive: TD&Q - by Dewie, started: 05-23-2006, last post: 2007-03-15 11:29:52 CET)
Ok Folks, I know that this has been talked about Many times (MANY MANY TIMES - All I can find is garbage threads that go no-where) But I am putting a 3.1 V6 from a '92 (I think... I need to check on this) with already mated 5spd Getrag Tranmission. The engine is definatly a 3.1 MPFI with coil-pack...
Score: 1000, Size: 35 bytes
|
| |
|
Put a PFF Search Box on your Site!