|
141:
|
3800 supercharger to intake plenum gasket. Sealant as well or no?
(Technical Discussion & Questions - by deezil, started: 08-06-2015, last post: 2015-08-11 01:37:53 CEST)
My Superchargers snout has decided it does not like it's bearings anymore.I have decided to just remove the whole SC and gut it, powdercoat it and rebuild it since it looks a little tired.The question I have is does the gasket between the SC and LIM need a sealant on both faces or is the gasket as...
Score: 633, Size: 73 bytes
|
142:
|
'92-'96 LT1 Intake Manifold 180 degree rotation. Any suggestions?
(Technical Discussion & Questions - by hdryder, started: 10-16-2016, last post: 2016-10-17 13:04:02 CEST)
I purchased an older Fiero swap with '95 LT that has the intake in the normal RWD position, with the throttle body on the passenger's side (RH) of the Fiero.I would be able to have much more room for T/B intake ducting and a colder air intake location if I can rotate the intake 180 degrees to get...
Score: 633, Size: 73 bytes
|
143:
|
How is the best way to remove the upper intake manifold?
(Technical Discussion & Questions - by mrstan, started: 02-21-2016, last post: 2016-02-22 17:03:01 CET)
Hi guys,I am working over my delapidated intake manifold on my 2.8 1988 GT.. I took all the bolts, throttlebody, hoses, etc off the intake, but it seems to be stuck fast. I am a little scared to stick the crow-bar under it and heave. Is there a trick to unsticking the thing or is it just a matter...
Score: 633, Size: 63 bytes
|
144:
|
Quarter window real intake
(Technical Discussion & Questions - by ssquire, started: 09-19-2013, last post: 2013-09-21 05:51:22 CEST)
I was wondering if you guys have seen any intakes that have been moved from the driver's side quarter panel to the driver's side window scoop? I'm beginning the process of preparing my car for paint and I was thinking about removing the side intake. Then I though it might be neat to have a nice...
Score: 633, Size: 34 bytes
|
145:
|
Question about intake manifold v6
(Technical Discussion & Questions - by zobari, started: 02-17-2019, last post: 2019-03-08 03:42:27 CET)
Hello,Could you tell me if the round mark is for the egr vacuum line (see the below picture please)https://imgur.com/a/uuepu44https://ibb.co/cYz1LZYThank you[This message has been edited by zobari (edited 02-17-2019).]
Score: 633, Size: 40 bytes
|
146:
|
1.6 vs 1.7 rockers with ported + dual throttle body intake
(Technical Discussion & Questions - by Winfield1990, started: 06-03-2014, last post: 2014-06-04 16:01:47 CEST)
I have around 100 miles on my motor , waiting for the cam to wear in before I swap rockers. I am still deciding on which ratio to get because I have ported lower , middle , and a dual throttle body upper intake. Along with some other minor things but that's pretty much the biggest improvement for...
Score: 633, Size: 71 bytes
|
147:
|
87 fiero gt 2.8 stock. What are cheap DIY upgrades for air intake, throttle body
(Technical Discussion & Questions - by FieroGT-987, started: 08-07-2013, last post: 2013-08-30 22:42:33 CEST)
Please help with some cheap DIY mods
Score: 633, Size: 93 bytes
|
148:
|
Intake manifold questions
(Technical Discussion & Questions - by Oregon88, started: 09-11-2020, last post: 2020-09-12 03:39:56 CEST)
Hey guys and gals. Hope all is well with y’all. While replacing my clutch I came across a broken EGR Tube, who knows how long it was broken, but it certainly had time to cover the inside of the intake manifold with LOADS of oil/dirt. It also covers the inside of the middle plenum and throttle...
Score: 633, Size: 34 bytes
|
149:
|
Anyone have a part number for SD4 intake gasket?
(Technical Discussion & Questions - by Raydar, started: 04-07-2015, last post: 2015-04-08 04:23:49 CEST)
As the title says...I'm looking for the part number for an SD4 intake manifold gasket. For the 775 head, and I'm guessing most others. This is not the raised port (801?) head. That is the only exception I know of.Any help will be appreciated.
Score: 633, Size: 55 bytes
|
150:
|
3800 Hoses and intake
(Technical Discussion & Questions - by SSN669chris, started: 12-24-2015, last post: 2015-12-26 03:54:09 CET)
I have gotten through the physical install of a 3800 n/a 4t65HD series 3 with a series 2 computer.Thanks to the information from Ryan I have the parts necessary to build the fuel regulator and will be sending off the computer Monday to him. Thanks to Rob I have a handle on the wiring.Are there...
Score: 633, Size: 33 bytes
|
| |
|