|
|
11:
|
Improving Stock Intake vs Trueleo Intake
(Archive: TD&Q - by FieroGT_DK, started: 01-23-2010, last post: 2011-05-02 10:43:08 CEST)
I recently put a 3.4L ohv (PR) engine in my Fiero GT '87 Aut.The engine is new and stock with the standard cam, 17lb injectors ,sinister chip, fiero store heat coated sprint manifold/y-pipe and ocelot exhaust and no cat.The waterdeflector in the wheelwell has been removed and a pipe has been...
Score: 1000, Size: 53 bytes
|
12:
|
Anyone used the 3.4 intake instead of the 2.8 fiero intake on their 3.4 engine swap
(Archive: TD&Q - by David Gamache, started: 04-04-2001, last post: 2001-09-24 23:34:55 CEST)
I am getting ready to reassemble the 3.4 with the fiero 2.8 accessories after I locate someone in CA that can re-drill or has a template to re-drill the starter holes on the block at a reasonable cost. I think the fiero upper intake looks nicer but the 3.4 intake design takes less gaskets and...
Score: 1000, Size: 99 bytes
|
13:
|
I need HEEEEELLLPPP with my Dual TB intake (The Enterprise intake)
(Archive: TD&Q - by goatnipples2002, started: 10-01-2006, last post: 2007-03-15 11:29:21 CET)
I have had my intake for a month or so I for the love pf god I cannot figure out how to get both TBs to activate at the same time. I had it rigged with some L brackets and a steel bar but when it swung up it would hit the deck lid. I have tried adapting the cruise cable but that hasn't worked at...
Score: 1000, Size: 84 bytes
|
14:
|
Will I need the intake manifold plates for an Allante intake on a 4.9?
(Archive: GFC - by Letsbuildanexotic, started: 09-21-2011, last post: 2013-03-14 10:19:51 CET)
As the thread states, will I need these?http://cgi.ebay.com/ebaymot...&hash=item27bba9990fChris
Score: 1000, Size: 90 bytes
|
15:
|
True Cold Air Intake vs. High Performance Air Intake
(Archive: GFC - by FirstDrCar, started: 12-10-2011, last post: 2013-03-14 10:19:28 CET)
Which is better for air flow? horse power? gas mileage? etc.What is better to have a better iron duke?http://rodneydickman.com/ca...th=22&products_id=70vs.http://www.tlg-store.com/4c...ke_p/fieroeng017.htmTrue CAI vs. High Performance AI....Thanks!If this topic is more better suited for the...
Score: 1000, Size: 65 bytes
|
16:
|
who makes 3800sc s2 cold air intakes?
(General Fiero Chat - by FieroCanada, started: 02-17-2014, last post: 2014-02-18 23:41:30 CET)
Need an intake, and taking a look at quality intake options,so far i know WCF makes themhttp://www.westcoastfiero.c...ntake_installed.htmlanyone else?[This message has been edited by FieroCanada (edited 02-17-2014).]
Score: 633, Size: 49 bytes
|
17:
|
Contest- Who has the crappiest intake tube? Winner has to buy Cliff a beer!
(General Fiero Chat - by cam-a-lot, started: 05-17-2015, last post: 2015-05-30 13:49:59 CEST)
I am pretty sure I will win this competition. My swap was done by a local gentleman who has done more then 50 3800 swaps in Fieros.. I decided to check on my air filter yesterday. The Intake tube literally fell apart in my hands.. It uses half of a rubber tube for the LQ4 MAF, and half of the...
Score: 633, Size: 85 bytes
|
18:
|
Intake removal question. Help requested.
(General Fiero Chat - by CoolBlue87GT, started: 03-20-2014, last post: 2014-09-01 01:36:42 CEST)
How is the hose attached to the bottom of the intake ? The one I'm looking at in the photo, is the hose nearest the distribtor with the blue tape. Is there a clamp, or just slide on ? How hard is it to remove this hose ?. I may be removing the intake & valve covers to refinish & to replace the...
Score: 633, Size: 54 bytes
|
19:
|
Possible bad intake?
(General Fiero Chat - by silver 85 sc, started: 08-24-2015, last post: 2015-08-29 04:50:26 CEST)
Here's the scoop. I have an '84 SE with a rebuilt motor, I have been going through about a gallon of coolant a month. So I started with the obvious. Old radiator, replaced, water pump, replaced, heater core, replaced, all lines have been inspected and are bone dry. There is no coolant in the oil,...
Score: 633, Size: 33 bytes
|
20:
|
Fieor Intake manifold power coat
(General Fiero Chat - by Cajun, started: 01-17-2016, last post: 2016-01-18 23:05:23 CET)
Thought I would attempt to redo my spare intake manifold. Actually have my son do the work. If I say so myself it didn't turn out half bad. Now I need to swap out the existing one.
Score: 633, Size: 38 bytes
|
| |
|
Put a PFF Search Box on your Site!