|
1711:
|
4.9 in 88 Measurements???
(Archive: TD&Q - by Cplensdorf, started: 05-25-2004, last post: 2004-10-15 10:18:03 CEST)
I asked this once before, but I think I buried it in another thread....Does anyone have any quick out-of-car measurments that I can use to verify the placement of my 4.9/4T60 on an 88 cradle?
Score: 499, Size: 38 bytes
|
1712:
|
4.9 swap --- Temp sensor pin identification
(Archive: TD&Q - by falcon_ca, started: 10-07-2009, last post: 2011-05-02 10:43:48 CEST)
I am in the process of building the engine harness for the swap of a 91 4.9 V8 into my Formula.I follow the instructions from different threads, there is a lot of them, and they are all interesting.I bought a temperature sender with three connectors as suggested in Mickey_Moose's thread and he is...
Score: 499, Size: 56 bytes
|
1713:
|
Correct Temp sensor 4.9
(Archive: TD&Q - by bristowb, started: 04-27-2011, last post: 2013-03-14 10:12:08 CET)
I picked up a Temp sensor for a 1998 3800SC motor for my 4.9 build is this the correct Temp sensor?
Score: 499, Size: 34 bytes
|
1714:
|
Have to pull tranny to 4.9 what is my best option ?
(Archive: TD&Q - by 86fieroEarl, started: 12-16-2003, last post: 2004-07-10 10:38:40 CEST)
Welp I have a bad th 125 tranny in my 4.9 swap That has bigtime slipage, After doing a fluid and filter change it still continues to slip so the only thing I can see is worn clutch packs. I did very little shopping around the other day and asked amco transmissions how much would they charge to...
Score: 499, Size: 65 bytes
|
1715:
|
What is the maximum speed GM limits 4.9s from the factory?
(Archive: TD&Q - by Mastermind, started: 07-30-2003, last post: 2003-11-10 11:06:42 CET)
Any ideas?
Score: 499, Size: 71 bytes
|
1716:
|
4.9 exhaust help
(Archive: TD&Q - by clintrock, started: 01-21-2006, last post: 2006-08-11 13:10:13 CEST)
Ok I went and bought an 80 series Flowmaster for my 4.9 swap. I dont need a cat and I would like to keep the trunk. I've been all over town and I can't find anyone who sells mandrel bent pipes. So my only solution is summit or jegs. They both seem to have decent prices. I've seen some nice installs...
Score: 499, Size: 28 bytes
|
1717:
|
4.9 running rich and backfires
(Archive: TD&Q - by rroberts, started: 06-13-2003, last post: 2003-11-10 11:10:54 CET)
I havn't looked to far into this. I did hook up the Snap-On tester and all it said was wrong was the IAV but when I look at the valve with the eng running it is working. I think it is setting the coad because the engine won't stay at a even RPM. I did notice that the timing was going up and down...
Score: 499, Size: 41 bytes
|
1718:
|
4.9 cracked head?
(Archive: TD&Q - by milkman, started: 06-02-2008, last post: 2009-09-07 11:04:30 CEST)
still trying to finish up my 4.9 swap. I put my exhaust on, started it up and noticed white smoke/steam coming out of the right dual. I shut it down, waited for it to cool off and checked the water level. Sure enough it was low. How common is it for the 4.9 to have a cracked head and or a blown...
Score: 499, Size: 27 bytes
|
1719:
|
Seanpaul's 4.9 Questions.....
(Archive: TD&Q - by Seanpaul, started: 08-06-2003, last post: 2003-11-10 11:05:53 CET)
Ok, real soon it's gonna happen about 4 months, and I'm there....I'm going to get a 92 setup.I want to keep it all stock, so it's simple, as this is my first engine swap...I'm up to any tricks that can be done, that are simple...but as far as wiring, that's what I don't want to deal with...Does...
Score: 499, Size: 40 bytes
|
1720:
|
4.9 intial start - some questions...
(Archive: TD&Q - by GT, started: 04-27-2006, last post: 2007-03-15 11:34:11 CET)
Well, I finally got the 5.0 Caddy running. I have not yet hooked up the O2 sensor as I don't have the exhaust on it. But I have a couple of concerns after my first short test drive yesterday:1) I have a 4-puck stage III Spec clutch and a Getrag. The clutch chatters when you first start off. Is...
Score: 499, Size: 41 bytes
|
| |
|