|
|
11:
|
Clutch not fully disengaging
(Technical Discussion & Questions - by fierofinder, started: 05-19-2016, last post: 2016-07-18 22:34:55 CEST)
First off the master and slave cylinders are new and I do have Rodney's double seal kit in the slave. With a clear hose connected to the bleeder valve I see no air bubbles when bleeding. I'm working with an 88 with getrag and with my research I have learned that the pushrod at the slave cylinder...
Score: 775, Size: 40 bytes
|
12:
|
Chattering noise when clutch disengaged, 88, 5-speed, stock V6 engine
(Technical Discussion & Questions - by rinselberg, started: 08-04-2014, last post: 2015-04-30 00:43:22 CEST)
I searched here, and there was this other thread, but this is different.I only hear the noise when the clutch is disengaged. When I am idling in neutral at a stop light, there is no noise unless I rest my foot on the clutch pedal. Even the slightest pressure on the clutch pedal brings on the noise....
Score: 775, Size: 80 bytes
|
13:
|
Clutch not disengaging completely
(Technical Discussion & Questions - by LovesGoldens, started: 05-25-2017, last post: 2017-05-26 02:51:10 CEST)
I have replaced 3 each master and slave cylinders on my '88 Fiero 5 speed transmission. Clutch will not fully disengage.. Only get 3/4" movement on the slave. Tried different bleeding procedures with no effect. Am I getting the incorrect parts? What is the original bore dimensions of the cylinders?...
Score: 775, Size: 46 bytes
|
14:
|
Clutch half disengaged
(Technical Discussion & Questions - by Xenoblast, started: 02-12-2022, last post: 2022-02-13 20:49:01 CET)
87 GT 5 speedI had this problem a while back when I was moving houses, but it never came back so I ignored it. But I drove for an hour without taking it out of 5th gear, so when I finally exitted the highway the clutch was half disengaging. I know that for sure bc reverse was grinding if i tried...
Score: 775, Size: 32 bytes
|
15:
|
New clutch in my fresh 4.9 swap will not disengage
(Technical Discussion & Questions - by Meanspiritdave, started: 10-22-2014, last post: 2014-11-11 20:27:51 CET)
I have been slowly but surely building my first swap. The car is an '86 GT with the Muncie 4 speed. We have installed a '92 4.9 utilizing a flywheel from LSC, and the 84-86 4spd 9.75" HD Clutch Kit from the Fiero store. Everything went together perfectly. The motor is running great. Now the clutch...
Score: 775, Size: 65 bytes
|
16:
|
Clunking sound when disengaging clutch if going From fwd to reverse
(Technical Discussion & Questions - by Lou and Blue, started: 08-11-2016, last post: 2016-08-15 07:38:03 CEST)
I don't know if it's the rear Axle going bad or the brake pad dragging or maybe even loose motor mount mount to Fiero Rog bracket.)If I go forward, stop, put it in reverse and let Off the clutch I hear a clunking or two as it backs up. Then it's ok as I keep reversing , then I stop, put it in first...
Score: 775, Size: 81 bytes
|
17:
|
3.8 sc 88gt clutch doesn't disengage
(Technical Discussion & Questions - by tomsablon, started: 11-28-2015, last post: 2016-03-01 01:54:43 CET)
the clutch doesn't disengage fully. it's a spec stage 2 with about 6000 miles and it grips fine. i replaced the throwout bearing with the clutch.i raised the back of the car on ramps and bled everything i think. i was wondering if measuring the stroke of the clutch arm right where the piston rod...
Score: 775, Size: 47 bytes
|
18:
|
Clutch won't disengage
(Technical Discussion & Questions - by JackyLee93, started: 05-29-2017, last post: 2017-06-01 21:19:37 CEST)
Hi guys new here. Got a 1984 Pontiac Fiero 2m4 with a 4spd Muncie. Before you say it, yes I've gone through the steps to properly bleed the hydraulics and have looked everywhere for any explanation. Got a new slave cylinder and brand new clutch kit in. I have movement from the slave cylinder and...
Score: 775, Size: 33 bytes
|
19:
|
Clutch won't disengage! Help!
(Technical Discussion & Questions - by asgosnell, started: 03-14-2013, last post: 2016-01-16 23:48:56 CET)
Sorry for the paragraph in advance, just want to explain fully The clutch was having problems shifting into 1st and reverse a couple weeks ago, however only when running and all other gears worked fine. So I tried to bleed it and ended up breaking off the bleeder screw because it was so rusted...
Score: 775, Size: 39 bytes
|
20:
|
Clutch won't disengage....
(Technical Discussion & Questions - by I_N_J, started: 06-24-2016, last post: 2016-06-28 05:43:52 CEST)
I've been having issues with my car not wanting to go into 1st or reverse for a while. I decided to do something about it, and picked up a new slave cylinder. Put it in today and bled it, and... now I can't get it into any gear at all. If I start the car in 1st gear, it moves a bit. It creeps...
Score: 775, Size: 32 bytes
|
| |
|
Put a PFF Search Box on your Site!