|
|
1:
|
Yet another my clutch wont disengage thread
(Technical Discussion & Questions - by shemdogg, started: 05-15-2023, last post: 2023-05-24 05:46:27 CEST)
I read up on all the threads on this. I bled the clutch w the pump bleeder and w the gravity and 2 person method. Clutch feels great. Slave arm only moves about 5/8", clutch pedal is level w the brake, both I know are wrong. Suspected the pedal was bent but it looks square, even put my framing...
Score: 775, Size: 52 bytes
|
2:
|
Clutch half disengaged
(Technical Discussion & Questions - by Xenoblast, started: 02-12-2022, last post: 2022-02-13 20:49:01 CET)
87 GT 5 speedI had this problem a while back when I was moving houses, but it never came back so I ignored it. But I drove for an hour without taking it out of 5th gear, so when I finally exitted the highway the clutch was half disengaging. I know that for sure bc reverse was grinding if i tried...
Score: 775, Size: 32 bytes
|
3:
|
Clutch won't disengage
(Technical Discussion & Questions - by Saggy, started: 08-21-2020, last post: 2020-08-21 22:41:28 CEST)
I have a 1984 Fiero SE. when I got it, the provious owner said I had to pump the clutch to get it too work, and thats why it had been sitting for 3 years. I bled the clutch line and it worked just fine. Then, once I dealt with some other bits to get it on the road, I learned the issue was the...
Score: 775, Size: 29 bytes
|
4:
|
Clutch won't disengage
(Technical Discussion & Questions - by JackyLee93, started: 05-29-2017, last post: 2017-06-01 21:19:37 CEST)
Hi guys new here. Got a 1984 Pontiac Fiero 2m4 with a 4spd Muncie. Before you say it, yes I've gone through the steps to properly bleed the hydraulics and have looked everywhere for any explanation. Got a new slave cylinder and brand new clutch kit in. I have movement from the slave cylinder and...
Score: 775, Size: 33 bytes
|
5:
|
Clutch not disengaging completely
(Technical Discussion & Questions - by LovesGoldens, started: 05-25-2017, last post: 2017-05-26 02:51:10 CEST)
I have replaced 3 each master and slave cylinders on my '88 Fiero 5 speed transmission. Clutch will not fully disengage.. Only get 3/4" movement on the slave. Tried different bleeding procedures with no effect. Am I getting the incorrect parts? What is the original bore dimensions of the cylinders?...
Score: 775, Size: 46 bytes
|
6:
|
New clutch won't disengage, HELP
(Technical Discussion & Questions - by FieroCat, started: 10-14-2016, last post: 2016-10-18 00:32:41 CEST)
So I just finished rebuilding my 2.8 V6 engine and re-installed it in the car with a new clutch, throwout bearing and re-surfaced flywheel. And upon trying to put it in gear, I found that the clutch will not release. There is a good inch of throw in the slave cylinder, so no problems with the...
Score: 775, Size: 41 bytes
|
7:
|
Clunking sound when disengaging clutch if going From fwd to reverse
(Technical Discussion & Questions - by Lou and Blue, started: 08-11-2016, last post: 2016-08-15 07:38:03 CEST)
I don't know if it's the rear Axle going bad or the brake pad dragging or maybe even loose motor mount mount to Fiero Rog bracket.)If I go forward, stop, put it in reverse and let Off the clutch I hear a clunking or two as it backs up. Then it's ok as I keep reversing , then I stop, put it in first...
Score: 775, Size: 81 bytes
|
8:
|
Clutch not fully disengaging
(Technical Discussion & Questions - by fierofinder, started: 05-19-2016, last post: 2016-07-18 22:34:55 CEST)
First off the master and slave cylinders are new and I do have Rodney's double seal kit in the slave. With a clear hose connected to the bleeder valve I see no air bubbles when bleeding. I'm working with an 88 with getrag and with my research I have learned that the pushrod at the slave cylinder...
Score: 775, Size: 40 bytes
|
9:
|
Clutch won't disengage....
(Technical Discussion & Questions - by I_N_J, started: 06-24-2016, last post: 2016-06-28 05:43:52 CEST)
I've been having issues with my car not wanting to go into 1st or reverse for a while. I decided to do something about it, and picked up a new slave cylinder. Put it in today and bled it, and... now I can't get it into any gear at all. If I start the car in 1st gear, it moves a bit. It creeps...
Score: 775, Size: 32 bytes
|
10:
|
New Fiero Store HD Clutch - won't disengage
(Technical Discussion & Questions - by Synthesis, started: 05-09-2016, last post: 2016-05-14 05:26:07 CEST)
seajai and I spent this past weekend tearing the engine out of my 86GT and replacing the timing set (1+ inch of play without the guide), water pump, oil pan gasket and the flywheel/clutch/pressure plate and throwout bearing.We installed a brand new Fiero Store HD Clutch kit for the car to replace...
Score: 775, Size: 54 bytes
|
| |
|
Put a PFF Search Box on your Site!