Search in
Entire Forum + ArchivesResults 1641 - 1650 of 2203 for 4.9. Search took 0.053 seconds.

Previous  161 162 163 164 165 166 167 168 169 170  Next Sorted by Relevance | Sort by Date




 
1641:
4.9 ECM plug pins?   (Archive: TD&Q - by Mickey_Moose, started: 02-28-2004, last post: 2004-07-10 10:36:43 CEST)
Anyone have a part number or where to buy then from? I am looking for just the pins that are crimped onto the ends of the wires.thanks,Tim
Score: 499, Size: 33 bytes

1642:
4.9 swap question   (Archive: TD&Q - by Dragon1, started: 06-26-2003, last post: 2003-11-10 11:09:46 CET)
Do I need to trim the battery tray for clearance, and/or do I need to move the battery or can I mount it in the same place and not trim the tray??I am using the stock caddy alternator with an idler pully about where the smog pump used to bolt and then an empty air conditioning compressor for belt...
Score: 499, Size: 28 bytes

1643:
need help with my 4.9   (Archive: TD&Q - by wiccantoy, started: 02-17-2007, last post: 2009-02-19 10:46:08 CET)
O.K. here is where i am having problems. Hopefully someone on here can lend a hand. I have everything in my sig done to my 4.9. Now here is the problem. I have everything set to where it is supposed to be set at and when cold and under a load (driving down the road) it dogs down like there is a...
Score: 499, Size: 33 bytes

1644:
Anyone running a Superchips chip on their 4.9?   (Archive: TD&Q - by Mastermind, started: 07-23-2003, last post: 2004-02-23 13:38:01 CET)
Have you noticed a increase in performance? If so, is it worth it?
Score: 499, Size: 59 bytes

1645:
Autometer Air/Fuel Gauge and a 4.9 (eldorado dual O2)   (Archive: TD&Q - by Capt Fiero, started: 06-29-2005, last post: 2006-02-06 11:46:16 CET)
Ok so I wanted to use my O2 meter on my Caddy swap. Well my Caddy has 2 running O2 sensors and a 3rd bung that is not used. I have hooked the gauge up to one of the O2 sensors that is used, but the gauge is so slow to move it is crazy. According to the gauge, the O2 is reading near full rich as...
Score: 499, Size: 66 bytes

1646:
4.9 Intake Question   (Archive: TD&Q - by fffttt1, started: 12-07-2006, last post: 2009-02-19 10:46:24 CET)
Will the Allante 4.1 intake setup fit on the 4.9 motor? Thanks, Ray.
Score: 499, Size: 29 bytes

1647:
4.9 advice   (Archive: TD&Q - by 2-tone, started: 01-19-2003, last post: 2003-05-31 09:50:18 CEST)
well I,ve been away for a while.Now I.m back. finally got a 4.9 long block to put in my little Elenor. What year TBI off of the 4.5 is the best to use on a 4.9 for ease of getting it going? This motor will be mated up to a izusu 5-speed trans.What flywheel and clutch do I use? please advise. -B-
Score: 499, Size: 19 bytes

1648:
4.9 temp sensor?   (Archive: TD&Q - by geobass, started: 01-05-2005, last post: 2005-04-10 10:36:42 CEST)
Are you drilling and tapping into the water outlet for a fiero sensor or using a replacement for the Caddy ecm coolant temp sensor with a three prong connector?As always pics are nice.Thanks,George
Score: 499, Size: 26 bytes

1649:
Calling 4.9ppl, 4.9 Questions   (Archive: TD&Q - by Psychosis39, started: 06-29-2003, last post: 2003-11-10 11:07:52 CET)
I have a 4.9 out of a 1992 Seville STS, I notice my exhuast manifolds are different then the ones used in your swaps. Once I get the 4.9L in the car and everything; would I be able to take that car to the exhuast shop and have them bend me a custom exhuast? Would it fit with the seville manifolds??
Score: 499, Size: 43 bytes

1650:
What are you using for a 4.9 swap dogbone mount on the motor?   (Archive: TD&Q - by MulletproofMonk, started: 04-18-2009, last post: 2010-04-21 09:18:54 CEST)
I'm going to make a junkyard run soon and was curious what people are using for a 4.9 swap dogbone mount on the motor?
Score: 499, Size: 79 bytes



Previous  161 162 163 164 165 166 167 168 169 170  Next Sorted by Relevance | Sort by Date

Entire Forum + Archives

Search in
Search Help | Back to Forum | Contact Us
Put a PFF Search Box on your Site!

© 2006 Pennock's Fiero Forum